image
Request a Quote
Conceptual comparison of shorter and longer fold-out solar arrays deployed in separate lanes at a temporary project site

Conceptual application illustration. Panel counts and proportions in this scene do not represent certified model dimensions or an installed Hinergy project.

Choosing a mobile fold-out solar array starts with the job it must support: the daily energy target, the times electricity is needed, the available ground and the equipment receiving the solar DC output. A larger array offers more generation potential, but it also needs more deployment space and a suitable electrical path for that additional energy.

Quick answer: Evaluate the smaller array when its site-specific energy estimate, transport requirements and deployed dimensions fit the project. Evaluate the larger array when the additional generation can be used, stored or otherwise accepted, and its footprint and PV input requirements also fit. If neither option meets the load, access or electrical conditions, revise the system plan before ordering.

In this 15 kW vs. 30 kW mobile solar array comparison, those figures describe the two search categories. Hinergy's current reference configurations are PowerFold-GL144 at 14.4 kW DC and PowerFold-GL288 at 28.8 kW DC. Use the actual quoted ratings for calculations; neither number is a continuous AC supply rating.

What Do 15 kW and 30 kW Mean for Hinergy Arrays?

The mobile fold-out solar array system is the PV generation assembly. The linked modules fold onto a handling base for transport and unfold on prepared ground. Battery storage and conversion equipment belong to the agreed project scope.

The following reference data show why the choice involves more than doubling the module count.

Selection point

PowerFold-GL144

PowerFold-GL288

What it changes

Actual PV capacity

14.4 kW DC

28.8 kW DC

The starting point for a solar energy estimate

Reference modules

36 × 400 W

72 × 400 W

Module count and the circuit design to verify

Stowed dimensions, L × W × H

1,425 × 2,150 × 1,130 mm

2,695 × 2,150 × 1,130 mm

Carrier space, access and the handling plan

Deployed equipment, L × W

31.79 × 2.15 m

63.42 × 2.15 m

The continuous equipment layout to accommodate

Reference net / gross shipping mass

735 / 765 kg

1,455 / 1,495 kg

Handling capacity and shipment planning

PV connection

MC4 DC

MC4 DC

Connector form; electrical compatibility still needs checking

Listed optional storage, power / energy

12 kW / 32 kWh

25 kW / 64 kWh

A separate storage option, not the array's AC rating

These are published reference figures, not a substitute for the current datasheet, approved drawings and quotation. Deployed dimensions exclude working clearances. Confirm the packed shipment and all separately supplied equipment rather than treating the array's listed mass as the complete project shipment.

Start With Daily Energy, Simultaneous Demand and Overnight Loads

Prepare a load schedule before selecting a 15 kW-class or 30 kW-class deployable PV array. Record three different requirements:

  • Daily energy, kWh/day: sum each load's running power multiplied by its operating time, using measured duty cycles where possible.

  • Simultaneous demand and starting events, kW or kVA: identify equipment operating together, motor-start requirements and their duration. These affect conversion and supply capability.

  • Energy outside the solar window, kWh: identify overnight services and the required backup duration. These affect usable storage and the recharge plan.

For example, a 3 kW load operating for ten hours consumes 30 kWh. A 10 kW load running for three hours also consumes 30 kWh. Their daily energy totals match, while their power requirements and operating schedules can lead to different system designs.

For construction sites, separate cabins, communications, lighting and monitoring from machinery or other production loads. The construction site solar power sizing guide develops that load brief in more detail. Do not assume that either array alone will run every load on a site.

Check Ground Space, Shipping Mass and Handling Access

Confirm a usable layout, rather than total land area alone

The reference unfolded lengths are 31.79 m for GL144 and 63.42 m for GL288, both at 2.15 m equipment width. Their rectangular equipment envelopes calculate to approximately 68.3 m² and 136.4 m². These are not complete installation areas or illuminated module areas.

A site can have enough total square metres and still lack a clear strip for the approved layout. Allow separately for working access, cable routes, receiving equipment, drainage and the project restraint arrangement. Review shading along the complete deployed length. Do not assume that a long array can be split, bent or arranged in several lanes unless the approved design allows it.

Reference deployed lengths of 31.79 m and 63.42 m and gross array shipping masses of 765 kg and 1495 kg for GL144 and GL288

Length bars use one scale; diagram width is illustrative. Equipment envelopes exclude additional access and working space. Confirm dimensions and the complete packed shipment against current documents.

Check the move at both ends

Review the carrier, loading route, unloading equipment, approved lifting or forklift arrangement, load centre and site access. Equipment lifting capacity alone does not establish that a particular handling operation is suitable.

The smaller array has a lower listed shipment mass and shorter reference footprint. Whether that makes a move simpler depends on the available vehicle, route and handling equipment. Compare the full relocation process, including isolation, stowage and securing for transport, using the mobile solar array deployment and stowage guide.

Screen Both Capacities Against the Same Solar Assumptions

Use the project location, operating season and approved deployed geometry to estimate production. Equivalent peak sun hours measure solar energy on the module plane; they are not the number of daylight hours. If module banks face different directions or slopes, assess them separately.

For a transparent first comparison, assume 4 equivalent peak sun hours per day and an illustrative 0.80 net AC yield factor:

Illustrative daily AC energy ≈ actual DC capacity × 4 × 0.80

This gives about 46.1 kWh/day from 14.4 kW DC and 92.2 kWh/day from 28.8 kW DC. The factor is an assumed combined PV/conversion allowance, not measured Hinergy efficiency, guaranteed output or a modelling-tool default. The boundary is a suitably sized conversion stage's AC output, before additional battery-path losses, unaccepted surplus and dispatch restrictions.

For the reverse calculation, divide the target daily AC energy by the same assumed yield:

First-pass PV baseline, kW DC ≈ daily energy target ÷ (4 × 0.80)

Illustrative daily AC energy target

Calculated PV baseline

Which option enters further evaluation?

30 kWh/day

9.4 kW DC

GL144 can enter the next checks; GL288 would need a reason for the additional capacity

60 kWh/day

18.8 kW DC

GL288 enters the next checks; GL144 falls below this energy target under these assumptions

110 kWh/day

34.4 kW DC

Neither single reference array reaches this energy target under these assumptions

Three illustrative daily energy targets of 30, 60 and 110 kWh screened into PV baselines of 9.4, 18.8 and 34.4 kW DC using four peak sun hours and an assumed 0.80 factor

These are hypothetical energy screens, not project recommendations. Storage losses, operating reserve, starting loads, hourly balance and physical/electrical compatibility require separate assessment.

For more sun-hour scenarios and monthly/annual estimates, read the mobile solar array energy output guide.

Use the result to shortlist equipment. A daily surplus does not prove overnight supply, and a daily shortfall does not rule out an array designed to provide only part of a hybrid site's energy. State the intended solar contribution and identify what supplies the balance.

NLR PVWatts provides location-based PV production estimates and monthly or hourly AC results. Its grid-connected energy estimate does not establish off-grid autonomy. The JRC PVGIS manual describes resource and off-grid modelling options. No location-specific simulation has been run for the examples above.

Match the PV Array to the Inverter, BESS and Backup Plan

Confirm that the receiving equipment can accept the array

A 30 kW inverter label does not, by itself, confirm compatibility with the 28.8 kW array. Check permitted PV capacity, the MPPT operating range, temperature-corrected open-circuit voltage, operating current and short-circuit current for each input. Use the approved string and circuit arrangement.

The connection review also covers connector compatibility, cables, protection, isolation and the intended operating mode. On the AC side, confirm phase, voltage, frequency, continuous output and startup capability for the actual loads. Matching MC4-style connectors is not proof that the complete system is compatible. Use the BESS and hybrid inverter integration guide to prepare the electrical brief.

Size storage for its own task

The listed 12 kW / 32 kWh and 25 kW / 64 kWh options describe separate reference storage packages. Verify what each power rating means, the usable energy, charge/discharge limits, temperature limits and control compatibility in the selected equipment's documentation.

For an overnight load, calculate its energy requirement and the permitted discharge window, then assess how the battery will recover while daytime loads are also running. The DOE solar and storage overview distinguishes storage power from energy and explains the losses associated with storing and retrieving electricity.

For remote sites and field camps, agree on the reserve, acceptable interruption and generator or grid backup strategy. Adding panels cannot resolve an undersized inverter, incompatible input or inadequate nighttime storage by itself.

When Should You Evaluate the Smaller or Larger Array?

Evaluate GL144 when the lower capacity fits the complete brief

The 14.4 kW reference array is worth evaluating when the project-specific energy target fits its modelled contribution, the shorter layout fits the site and the transport and receiving equipment suit the configuration. This may apply to a limited set of site services or to solar supplementation alongside another source. Application labels alone are insufficient.

Evaluate GL288 when the extra generation has a defined use

The 28.8 kW reference array is worth evaluating when more solar energy is required and the site can accommodate its longer layout and shipment. Confirm that daytime demand, storage charging or another approved route can accept the additional generation. Otherwise, curtailment or unused surplus may reduce the benefit of the larger array.

Rework the system when both options fail a key check

Neither configuration is a final answer if the required operating-season energy exceeds the plan, the approved layout cannot fit, access is unsuitable or electrical limits cannot be met. Options may include changing the solar contribution, moving flexible loads, revising storage/backup, or engineering another configuration. Confirm any alternative before purchase.

Compare the Complete Project Scope Before Ordering

Compare quotations with the same boundaries: array, electrical conversion, storage, protection, cables, handling, freight, site works, commissioning and documentation. Confirm which items are included and who handles each interface. The larger array's purchase price is not the only cost difference, and twice the PV capacity does not establish twice the complete project cost.

Consider the expected operating period and relocation frequency. Future expansion is a design requirement to document, rather than an automatic feature to assume. The mobile fold-out solar array cost guide explains the quotation inputs without substituting a generic installed-system price.

Request a Capacity Selection Review

Send Hinergy the location and operating months, load schedule, daily kWh, simultaneous and starting demand, overnight requirement, usable site length/width, transport access and existing BESS/inverter details. Request current model data, deployed drawings and the proposed supply scope so both options can be assessed on the same basis.

Frequently Asked Questions

Does a 30 kW mobile solar array supply 30 kW continuously?

Is a larger foldable solar array always better for a construction site?

Can I combine two smaller arrays instead of choosing one larger array?

Which mobile solar array needs less ground space?

Can I choose capacity using daily kWh alone?

Are batteries and an inverter included with either array?

Sources and Calculation Basis

Reference dimensions, module counts, masses and storage options come from the current Hinergy system page and must be reconfirmed for the quoted model. The worked examples use a stated 4-hour solar-resource assumption and 0.80 factor; they are independent planning calculations, not measured production, a performance guarantee or a software simulation. Technical background: PVWatts, the JRC PVGIS manual and DOE solar/storage basics.